电话：15010245973同微信/010-51658042/
手机：15010245973/17316029570
传真：010-57553286
邮编：100142
E-mail:1733477181@qq.com
http://www.hengaode17.com/
地址：北京市海淀区阜成路

您当前的位置：首页 >> 产品展示 » 其他专用仪器仪表 » 杨氏模量测定仪HADYMC-1

杨氏模量测定仪HADYMC-1

1.杨氏模量测定仪型号:HADYMC-1

望远镜放大倍数:30倍物镜有效孔径42㎜

视场角1°26′、砝码7个、光杠杆：φ40㎜带重锤平衡装置、测量架、水平仪

备注：1米、1.8米选

2.汽车排气分析仪排气分析仪型号：NTP1-HPC302

主要能特点：

用于测量汽车排放废气中的HC、CO、NOx气体浓度，采用外术，口关键零件组装而成。具有亮度数码显示，自动校零，自动数据线性化处理，气路阻塞时自动报警，故障时自动诊断所在单元，打印测试之日期、时间能，配内置打印机（或模拟输出接口或RS－232A数字串行通信接口），可行自由怠速和双怠速测量，具有操作方便，测量数据，作稳定等特点。

主要术参数：
测量范围 HC：0～10000×10-6（ppm）vol
CO: 0～10 ×10-2(%)vol
NOx :0～4000 ×10-6（ppm）vol
示值误差 HC±12 ×10-6（ppm）vol(误差)或±5%(相对误差)
CO±0.06×10-2(%)vol (误差)或±5%(相对误差)
NOx ± 25×10-6（ppm）vol(误差)或±4%(相对误差)
重复性重复误差≤±2%
分辨率 HC：1×10-6（ppm）vol
CO: 0.01×10-2(%) vol
NOx:1×10-6（ppm）vol
稳定性自动校零，量矩漂移≤±3%
预热时间 8min（可预热3min应急检测）
响应时间 95%响应不大于10秒
输出方式数字直读显示，可附打印机打印气体名称，浓度zui大值，测
试时间、日期等。可附接口与计算机联网
环境条件温度0～40℃，相对湿度≤90%
电源 AC100-240V 50Hz 或DC12V（选加电源逆变器）
消耗率50VA
外形尺寸 420mm(长)×310mm(宽)×170mm()
重量约9KG

Main Features:
Used to measure vehicle emissions of HC, CO, NOx gas concentration, using advanced foreign technology, import the key components assembled. With a high-brightness digital display, automatic zero, linear automatic data processing, auto-alarm when the gas line blocking, fault diagnosis where the unit automatically and print testing date, time functions, with built-in printer (or the analog output interface or RS -232A digital serial communication interface), can be freely idling and dual idling measure, with easy operation, accurate measurement data, work stable and reliable characteristics.

Main technical parameters:
Test Scope：HC：0～10000×10-6（ppm）vol
CO：0～10×10-2(%) vol
NOx：0～4000×10-6（ppm）vol
Shows the value error：HC ± 12×10-6（ppm）vol (absolute error)or± 5% (relative error)
CO± 0.06×10-2(%) vol (absolute error)or± 5% (relative error)
NOx±25×10-6（ppm）vol ( absolute error) or ±4%(relative error)
Stability：Automatic zero, volume moments drift ≤ ± 3%
Repeatability：Repeat error ≤ ± 2%
Resolution：HC：1×10-6（ppm）vol
CO：0.01×10-2(%) vol
NOx：1×10-6（ppm）vol
Response Time：95% of the response to no more than 10 seconds
Warm-up Time：8 min（May the preheating 3min urgent examination）
Output Mode：Digital direct-reading show that gases can be attached printer name, the
concentration maximum, average and minimum test time, date, etc.. Can be attached to interface with the computer network
Environmental conditions：Temperature 0 ~ 40 ℃, relative humidity ≤ 90%
Power：AC100-240V 50Hz or DC12V (select plus power inverter) Power
consumption 50VA
Dimensions：420mm (length) × 310mm (width) × 170mm (H)
Weight：about 9kg

3.摩托车排气分析仪摩托车排气检测仪型号：NTP1-HPC211

主要能特点：
分体式结构设计，操作方便，按新标GBl9758-2005术要求研制；
采用内置流式取样术，专用测量摩托车急加速、怠速况时的烟度；
亮度数码显示，口关键零件组装而成；
采用流式耐温的特殊取样探头，采样稳定、、方便；
丌机预热时间10分钟，并自动调零；
数据自动线性化处理，可显示不透光度N、光吸收系数K；
出现故障时自动显示故障代码；
附有自动时钟显示，内置打印机(RS—232或模拟接口联网)供选择。
主要术参数：

测量范围不透光度N: 0～

光吸收系数K:0～90.65m^-1

示值误差 ≤±2%

稳定性自动校零，量矩漂移≤±1%/4h

分辨率 0.1%

响应时间 1S±0.1S

输出方式 LED(4位)显示，可附打印机，打印出5组急加速烟度、怠速

烟度、光吸收系数的zui大值及平均值，测试时间、日期等，

可附接口与计算机联网

环境条件温度0～40℃，相对湿度≤90%

电源 AC100-240V 50Hz 消耗率150VA

外形尺寸控制箱：250mm(长)×310mm(宽)×170mm()

烟道箱：250mm(长)×170mm(宽)×170mm()

重量控制箱：4kg，烟道箱：5kg

Main Features:

◆Separated structural design, easy to operate, according to the new national standard GBl9758-2005 technical requirements for development.
◆With built-in full-flow sampling techniques, application-specific measurement of motorcycle hard phases of acceleration, idle condition when the smoke.
◆High-brightness digital display, import key components assembled.
◆Using a special full-flow high-temperature sampling probe, sampling a stable, accurate and convenient.
◆Ji machine warm-up time 10 minutes, and automatic zero adjustment.
◆Linear automatic data processing, can be displayed opacity degrees N, light absorption coefficient K.
◆Fails automatically displays fault code.
◆With automatic clock display, built-in printer (RS-232 or analog interface network) for selection.

Main technical parameters:

Test Scope：No light transmission N: 0～

Light absorption coefficient K: 0～90.65 m^-1
 Shows the value error：≤ ± 2%
 Stability：Automatic zero, volume moments drift ≤ ± 1% / 4h
 Resolution：0.1%
 Response Time：1S ± 0.1S
 Output Mode：LED (4-bit) display can be attached to the printer 5 groups hard phases

of acceleration smoke, idle smoke, the light absorption coefficient of

the maximum and the average test time, date, etc., can be attached to

interface with the computer network
Environmental conditions：Temperature 0 ~ 40 ℃, relative humidity ≤ 90%
Power：AC100-240V 50Hz Power consumption 150VA
Dimensions：Control Box: 250mm (length) × 310mm (width) × 170mm (H)
Flue Box: 250mm (length) × 170mm (width) × 170mm (H)
Weight：Control box: 4kg, flue box: 5kg

北京恒奥德仪器仪表有限公司

1.杨氏模量测定仪 型号:HADYMC-1

1.杨氏模量测定仪型号:HADYMC-1